Todos los idiomas del manual
Mobile IV Stand · Instrucciones de uso
English · Revisión 1.2 · Fecha de publicación
Desplácese para leer el manual completo. También puede abrir o descargar el PDF original.
Leer el manual como texto
Página 1
Mobile IV Stand — instructions for use
Model: IVSTND-260 | English | Rev 1.2 | 25 October 2026
Read these instructions before assembly and use. Keep them with the stand. This is a non-sterile, reusable
medical device for use by trained healthcare staff indoors.
Intended purpose
IVSTND-260 supports compatible infusion bags or bottles on four hooks and organises light clinical supplies
on a removable tray and lower basket. It also has supports for a waste bin and a compatible 1 L round sharps
container. Its contribution is mechanical support and access to supplies during care.
The stand does not pump, measure, administer or monitor an infusion and does not contact the fluid pathway.
It does not support or transport the patient.
Operating limits
Feature Limit or specification
Maximum combined load 10 kg across the hooks, tray and basket
All four hooks combined 4 kg total, distributed evenly
Removable tray 2 kg
Lower basket 4 kg
Minimum 1,200 mm · normal 1,750 mm · maximum 2,000 mm
Height adjustment
Measured from the floor to the top of the hooks
Base Five wheels, two fitted with brakes
Sharps container Compatible round 1 L container; follow its own instructions
The hook, tray and basket ratings may be used together within the 10 kg combined limit. Do not use
internal test loads as operating ratings.
Do not use the stand for
Sitting, standing, lifting, walking support or patient transport; mounting pumps or other equipment on the tube;
outdoor use; stairs; uneven or sloping floors. MRI suitability has not been established.
Stop use if the stand is unstable or a joint, height lock, wheel, brake or attachment is defective. Residual risks
include tipping or falling loads, unintended movement, pinching at clamps, snagged tubing, sharps injury and
cross-contamination from inadequate cleaning and disinfection. Keep within all load limits, use the brakes,
secure loads, keep hands and lines clear, and follow the sharps-container and cleaning instructions.
ECI-IFU-STND-260 | Rev 1.2 | Page 1Página 2
Assembly
Follow the sequence below using the matching supplied parts and hardware. Do not substitute fasteners.
1 Prepare the telescopic pole
Remove the hexagonal screw from the bottom of the pole.
Align the hand-tightening screw with the hole at the
telescopic connection and tighten it to secure the pole. No
tools required.
2 Fit the tray support
Slide the tray support onto the pole from the bottom and
position it at the required height. Secure it with the black T-
shaped screw supplied for the support. No tools required.
3 Attach the pole to the base
Insert the plastic cover into the central hole of the base.
Insert the pole and secure it from underneath with the M10
× 35 hexagonal combination screw. Use the 16 mm open-
ended wrench.
4 Fit the lower mounting plate
Remove the clamp from the lower mounting-plate assembly.
Position the plate and clamp around the pole as shown and
secure them with two M6 × 65 socket-head screws. Use the
5 mm hex key.
ECI-IFU-STND-260 | Rev 1.2 | Page 2Página 3
Assembly continued
5 Fit the basket
Align the basket with the threaded holes on the back of the
mounting plate. Secure it with two M4 × 12 socket-head
screws. Use the 3 mm hex key.
6 Fit the waste bin
Align the waste bin with the two hooks on the mounting
plate. Lower it onto the hooks and press down firmly. No
tools required.
7 Fit the sharps-container holder
Position the holder beneath the tray support, aligning the
two fixing holes shown. Secure it with two M4 × 10
countersunk hex-socket screws. Use the 2.5 mm hex key.
8 Fit the removable tray
Lower the stainless-steel tray into the tray support. Check
that it is seated securely before loading. No tools required.
After assembly, check every joint and attachment, both brakes and the height lock before placing the stand in
service.
ECI-IFU-STND-260 | Rev 1.2 | Page 3Página 4
Before each use
• Check that the stand is clean, the identification is readable and the surfaces are intact.
• Check all joints, clamps and accessories for secure attachment. Check that the tray is seated properly.
• Check that all wheels turn freely and both brakes operate. Apply both brakes and check that the stand stays
stationary.
• Support the upper tube before loosening the height lock. Adjust within 1200–2000 mm, retighten the lock
and check that the tube does not slip before loading.
• Distribute the hook loads evenly and keep within all individual and combined load limits.
Stationary use and movement
Apply both wheel brakes during stationary use. Keep fingers clear of sliding and locking parts. Keep the
infusion tubing clear of the wheels and any parts that could trap or pull it.
Before moving the stand, secure the containers and retract the sharps-container holder beneath the tray.
Release the brakes and push slowly, keeping the load stable. Approach small door thresholds cautiously; stop
and obtain assistance if the stand is unstable. Do not force the loaded stand over an obstruction.
Using the sharps-container holder
Pull out the holder for use and return it beneath the tray for movement. Use the compatible round 1 L sharps
container. Follow the container manufacturer’s fill limit, closure and disposal instructions. Do not place sharps
in the ordinary waste bin. The holder does not replace the container’s protective features or instructions.
Cleaning and disinfection
Remove supplies and waste safely. Remove soiling with a soft cloth and mild detergent in water. Wipe off
detergent with a clean damp cloth and allow the surface to air dry. Do not mix chemicals, immerse the stand,
pressure-wash it or use abrasive cleaners.
Disinfect with ready-to-use hospital surface-disinfectant wipes based on 70% isopropyl alcohol. Keep the
surface visibly wet for the full contact time stated on the wipe label, re-wetting if needed. Do not use other
disinfectant types.
Maintenance, service life and warranty
Specific scheduled maintenance: none. Carry out the before-use checks in this manual. Stop using a stand
with loose joints, a slipping lock, faulty brakes, damaged parts or surfaces that cannot be cleaned. Qualified
personnel must repair it and verify safe function before reuse.
Expected service life: at least five years under normal use, subject to the condition checks in this manual.
Warranty: two years. The expected service life is not an extension of the warranty.
ECI-IFU-STND-260 | Rev 1.2 | Page 4Página 5
End of use
Decontaminate the stand before disposal. Handle sharps and clinical waste separately under the applicable
local rules and the container instructions. Dispose of the stand’s materials in accordance with local
requirements.
Identification and reporting
Model: IVSTND-260. GTIN: 6980438430027. Identify an individual unit by its serial number and lot number on
the product label. Quote the model, serial number and lot when contacting EverCare about a defect or
incident. The 14-digit UDI-DI representation is 06980438430027. The house symbol on the label means
"Indoor use only".
Report any serious incident associated with the device to the manufacturer and to the competent authority of
the Member State where the user or patient is established.
Manufacturer
EVERCARE INNOVATIONS (SHENZHEN) CO., LTD.
Unit 102, Building J, No. 3 Xiang Yuan Pai Road, Pingxi Community, Pingdi Subdistrict, Longgang District,
Shenzhen, Guangdong 518000, China
Telephone: +86 136 3167 8692
Email: service@evercare-innovations.com
Website: www.evercare-innovations.com
European authorised representative
MDSS GmbH
Schiffgraben 41, 30175 Hannover, Germany
Document ECI-IFU-STND-260 | Rev 1.2 | 25 October 2026
ECI-IFU-STND-260 | Rev 1.2 | Page 5Página 6
Identification and document control
Mobile IV Stand
Medical device | Non-sterile | Reusable | Professional healthcare use
Model / catalogue number UDI-DI (GTIN, 14-digit representation)
IVSTND-260 06980438430027
The UDI-DI identifies the product model, not an individual unit. Read the unit’s serial number and lot number
from its product label. Match the model and unit identification on the device, packaging and accompanying
records before use. Do not substitute the manufacturer SRN for a product UDI.
Manufacturer identification
EVERCARE INNOVATIONS (SHENZHEN) CO., LTD.
Unit 102, Building J, No. 3 Xiang Yuan Pai Road, Pingxi Community, Pingdi Subdistrict, Longgang District,
Shenzhen, Guangdong 518000, China
Manufacturer SRN: CN-MF-000060301
Email: service@evercare-innovations.com | Telephone: +86 136 3167 8692
Website: www.evercare-innovations.com
EU authorised representative
MDSS GmbH
Schiffgraben 41, 30175 Hannover, Germany
Revision identification
ECI-IFU-STND-260 | Rev 1.2 | English | 25 October 2026
Changes since released Rev 1.0: full manufacturer address and identification page (manufacturer SRN,
model and GTIN, authorised representative and CE marking); residual risks; and cleaning and disinfection
instructions. The indoor-use-only label symbol is explained. Revision 1.1 was an unreleased draft.
ECI-IFU-STND-260 | Rev 1.2 | Page 6